According to the posting date, it’s been about 10 days since I last reported in on progress on Assist. I’ve had a couple of mis-alignments due to low lighting and inattention. Some I’ve picked out, others I saved as cautionary lessons. And I’ve taken a slight departure from my usual working cadence.

Here’s the latest in-hoop view.

Obviously I’m working voiding on the row of snaky, vaguely draconic S-shaped flowers. But I’m only half-way done with that, yet I’ve gone on to start (although not finish) the row of smaller fills underneath.

Why the partials?

Because it’s very likely I’ll be attending Arisia over the weekend. It’s a big science fiction convention here in the Boston metro area. There will be discussions, panels, and lectures to attend. I like to keep my hands occupied at such things, so I can better follow along without distraction. Therefore to minimize lap clutter and make this project more portable I want to have enough started with established repeats, so I can work “off book/screen” for the balance of the weekend. That plus using the chatelaine means quick convenience – nothing can be dropped or left behind as we migrate from one panel room to the next.

As far as difficulty, the voiding requires no pattern reference once the foreground repeat is established. The partial fills each have enough detail that I don’t need to refer back to those patterns, either. I can just copy what I’ve already worked. Note that that second one is rather far along. In that case I DID get lost and decided to finish that square out here at home and not trust to luck on the go.

I’ll probably start on the foreground of the next voided strip, too. Either below the four-box fill row, or above the three-box fill row that sits on top of the motto (seen peeking out at top, from the folds underneath the frame). Which one I’ll do will depend on which design I pick next. I think one that’s as wide as or very slightly narrower than the Assist strip will sit nicely at the growing pile north of the motto. Something wider and more demonstrative for below. How wide and how demonstrative is going to be a function of the very narrow nature of the composition as a whole. I only have 102 units across to play with. Lots of my drama queen voided/double running strapwork strips have repeats significantly wider than that. We’ll see.

And a working hint. You can see that I’m not stitching up to the red double-running stitch boxes outlining my fills. I’m leaving a one-unit strip of unworked linen between the red outlines and the fills. Usually I “fig-leaf” any partial stitches when working fills in spaces buy doing them first, then stitching a heavy outline around the fill area to cover all sins. This time I opted for a lighter look. The hint is if you look at the on-deck set I’m currently stitching, and the two completed sets above (visible as partials in and above the hoop) you’ll see that I lay down the first pass of double-running, then work the fill, then go back and complete the double-running by stitching the second pass. I’m doing this because counting those little dashes is immensely easier to do than trying to navigate by counting the stitches in a completed line.

The uncorrected mistakes to date? There are four, and I hang my head in shame.

First, my original basted guidelines were off by three units. The natural vertical center of the piece is three units to the right of my first go at basting. That I didn’t catch until I had finished the voiding on Assist. Voiding is not something that should be picked out by the faint-hearted, especially in silk on somewhat fragile vintage linen. So I adjusted my alignments rather than picking out. When I frame or finish this up as a scroll there will be some compensation to keep the final field even all the way around.

Second, I’m off by an entire unit somewhere between the vertical center and right guide line, probably with two one-thread width displacements in an earlier slubby or worn/fuzzy bit on the vintage linen. There I didn’t catch that until the first row of fills and Assist were done. Oops.

Third, that interlace box. The interlaces are not centered, again they’re off. This error I blame on SWI – stitching while intoxicated. We had a lovely bottle of champagne that evening, to celebrate the close of the holiday season, consumption of the last of our leftovers and cookies, and (in passing) to toast our 43rd wedding anniversary. Obviously it went straight to my head. I left that one in to warn me against similar excesses in the future.

And last, the width of the rightmost box on the current fill line. All of the ones in this row are supposed to be squares of 24 stitches. Except that one. There was only room for him to be 23 units wide. Now four boxes of 24 units plus three separators of two units each equals 102. But there he is, one stitch unit narrow. So it goes. I’ll pick a nice scattered fill with a half-drop repeat and no one will notice. Plus an added benefit of the strident, visually distracting alternating strips is that they break cadence. I can correct the count after the next one is done, and the correction will be difficult to see because of the solid red mass separating it from the fills above.

Oh. I did get a side benefit from the dissolute evening of sodden stitchery. I took the cork cage/bail from the bottle and twisted it into a spool holder for my chatelaine. I may go back and redo this with a silver tone one I had saved from last year’s bottle, but for now, it’s working well. The tiny spool of Corticelli Size A embroidery silk spins with little effort; just enough to make inadvertent unwinding unlikely, but easily enough to reel off what I need.

Will this piece be absolutely perfect? Nope. Far from it. And that doesn’t bother me because I have the next stitching project already in sight.