Tag Archives: book cover

BOOKMAKING 110: THE GRAND FINALE

And just like that, the cover is finished and mounted on the target book:

And pix of the thing off the book, Here’s the outside, with everything finished off and sewn flat:

And the inside (with my reverse in all its messy splendor):

To clarify what was done:

  1. As shown above, first I folded in the top and bottom flaps, but I didn’t bother to hem them – I just made sure that the raw edges were covered. There will be no wear and tear on these flaps, so there was no need to protect them further.
  2. Then I folded in the left and right flaps. BUT in this case, because the book covers may slide in and out of the stitched jacket (if the recipient decides to feature the other side as the front cover, or ever replaces the book itself) – I did hem them for stability.
  3. The next step was to stitch the placeholder ribbon to the underside of the top flap. I left it extra long, so that it could be fished out and used, no matter which of the two sides of the embroidered jacket were deemed to be the official front.
  4. After all four flaps were prepped I stitched the edges of the left and right flaps to the top and bottom edges of the book cover’s front.

Now that last step can be done in several ways. The easiest is a simple whip stitch or invisible hem. But I never take the easy way out. Instead, I went back and extended the green double running line that defines the top and bottom edge of my stitched area out along my fold. I couldn’t put the thing back into the frame, so I did it in hand. Then having two green lines established, I used the same green embroidery floss to work them together, following (more or less) the logic that people who make biscornu use to seam together the two squares that form their curious little pincushions. A good tutorial for that is here.

The image above shows my wobbly last minute double running stitches, and how I united them front and back to make a heavier edge seam.

Finally, having done all of the finishing work, I slid the book’s own covers into the flaps of my stitched jacket. Here you see them in place, with the handy help of a large corkscrew, since I was running out of hands to hold everything in place.

And so, taaa daah! A small book with a nifty cover. A stitched project that doesn’t take up wall space, that can be adapted to any size book you have on hand. Embellish a devotional book that means a lot to you; or at the other end of the spectrum, disguise a racy novel for discrete subway reading. Use any pattern that tickles your fancy. Or several if that’s what speaks to you. But whatever you do – enjoy, be creative, and feel the pride in coming up with something that’s specifically and personally meaningful to you.

This concludes my stitched book jacket tutorial. Please post questions if you have them – I’ll do my best to answer.

BOOKMAKING 109: STITCHING FINISHED, ON TO ASSEMBLY STEP ONE

I’ve finished all of the stitching on the book cover project, now on to turning the flat piece of cloth into the finished item.

Although I am a teensy bit disappointed that my centering efforts on the leafy side did not pan out, I think you can see that my guess was correct. Given the eccentric nature of this slow-descent repeat, it’s not obvious at all.

An interesting thing happened – density of color. The yellow used on the front and the back are the same – same color number, even the same skein. But the diagonal diamond voided fill used behind the leaves is more dense than the lattice weave used with the swirly flowers. And the swirly flowers, having nice dense centers and connector leaves show the red as being more intense, too. The colors present differently depending on the stitching designs chosen. Close diagonals will appear visually more dense and darker than stitches done “with the weave” – horizontally or vertically.

While density differences do manifest in monochrome, they mostly present as grey scale from a distance, or in some blackwork substyles – something akin to the cross-hatched lines that are used to indicate depth and shadow. But in polychrome it works a bit differently. Individual colors – the same colors in fact – will pop or recede, or even intensify, depending on the closeness and orientation of the line segments on which they are used.

Making up the Book Cover

Well, for me at least the fun part is over. Now for the less interesting but no less exacting half of the project – turning this flat piece of cloth into a book jacket.

As you recall, we have the flaps all neatly defined by basted lines. These I will just turn over, not bothering to finish off the raw edges. They will be well concealed once the thing is sewn together, plus the added bulk of a turned or rolled hem would distort the lie of the stitched part of the cover.

First I flipped the thing over, with the “good side” down, so I could fold my flaps to the back. I set the creases along the stitching lines and the basted guide lines, setting them with my iron. It’s easier to do if you finger-press first to get the precise fold line, then follow the finger-pressed creases up with a warm iron. (Ignore the blue ironing board cover stained with the ghosts of projects long past).

Finger pressing prior to ironing – you can see the stitched green perimeter along the very edge of the fold.

I started by setting the folds on the top and bottom edge, and then the left and right sides.

Then I trimmed off some of the excess fabric at the top and bottom. I didn’t bother trimming the left and right because there really wasn’t much to trim.

The next step was to fold everything in, and remove some of the bulk in the corners – note that I did not trim it all.

At this point with lots of nice, crisp creases in place, and no further need for the markings, I teased out all remaining bits of lavender basting thread.

On to the corners, to make them a bit sharp. There are other ways to do this, but origami-style “squash folding” to make a mitered corner is the simplest. I folded the corners in, ironed in the creases and pinned them for hand-tacking. And while I had the pin ball out (the needle-felted pin-puff is a treasured gift, made by Younger Spawn), I pinned the flaps to the body, although I will NOT be stitching them down..

And the last bit of prep was the stash-dive for a bit of red ribbon. That I will sew to the inside of the cover. It’s just long enough so it can be teased out to either the top or bottom, and will serve as an effective placemarker regardless of whether my recipient chooses the flower or the leafy side as the front cover.

Now off to do all of the tacking. The next post will cover sewing the end flaps in, to make the pockets into which the book covers will be slid. Before writing that bit up I want to experiment a bit, because I’d like those seams to be neat, and if possible – visible, and in green. We’ll see if that works out or if I punt and just stitch in the plain white sewing thread I am using for tacking and affixing the ribbon.

BOOKMAKING 108: RIPPING OUT AND RECOVERY

The last post of mea culpa probably left people wondering how it was going to all turn out. Here’s the result:

I only needed to tease out one straight line of stitching – the former rightmost edge of the previous side. Now the two borders join to make one larger mirrored strip that takes up the spine area and wraps around to be visible on the front and back. Not as I originally planned, but acceptable.

And I have been able to keep going on the second side, working my double leaves in red, and the diamond fill ground in yellow. Again, not as originally planned – the repeats will not be neatly centered left/right, but because this particular fill is eccentric, I bet it won’t be noticed by anyone who isn’t aware of the problem in the first place. (Mom, avert your eyes).

Now on to today’s submitted question:

How do you rip back?

With great care.

It’s very easy to inadvertently snip the ground cloth, and that’s a tragedy when it happens. But I have some tools that help.

The first thing is a pair of small embroidery scissors with a blunted tip. These are the latest addition to my ever growing Scissors Stable, and a recent holiday gift from The Resident Male. Note that one leg has a bump on it at the tip. That’s the side that is slid under the errant stitch being removed, to make the first snip. Although these are sharp all the way to the tip, the bump helps prevent accidentally scooping up and nipping the ground cloth threads.

To rip back taking all due care, I snip a couple of stitches on the FRONT of the work. Then I employ a laying tool and a pair of fine point tweezers for thread removal. The laying tool was also a gift from The Resident Male, and replaces a procession of thick yarn needles I used before I had it. My tool is about 3 inches long (about 7.6 cm).

Best Laying Tool

My pair of tweezers is one intended for use in an electronics lab. I found it in the parking lot of a former job, probably dropped by someone testing robots in the back lot. I tried to return it, flogging it around to likely techfolk for several months, but had no takers. Seeing it was to remain an orphan, I adopted it into a new fiber-filled life. I love it. It’s wicked pointy, and even with the dented end (probably damaged when it fell off the test cart onto pavement), does a great job of removing tiny thread bits.

Having snipped the threads on the front, I use the laying tool’s point (augmented by the tweezers) to tease out the stitches in the reverse order they were worked, doing it from the back. Luckily this style of work has a logical order and it’s usually pretty easy to figure that out. But in some cases it gets harder. When that happens, it’s another judicious snip on the front, followed by use of the tweezers from behind to remove the thread ends for discard. (While I can sometimes recover/reuse a live thread after I catch a mistake of a few stitches, in general if the run is long, or I’ve ended off the strand there’s little point in trying to save it and stitch with the now-used and damaged/fuzzy piece of thread.)

If the color is in the least bit friable and liable to crock on the ground fabric, I cut more and pull less – making sure to remove all threads from the back rather than pull them forward to the front. This minimizes color/fuzz shed on the front, public side of the work.

If any snipping needs to be done on the back, flat and parallel to the ground, I pull out another resident of my Scissors Stable – a pair of snips I bought at the SCA Birka marketplace event, two years ago. They look like this:

These were a great buy. Inexpensive, super-sharp (I think the snipping action helps keep them sharp), and because they are not held like finger-hole scissors, very easy to manipulate to snip close and flat to a surface.

And what to do if there are fuzzy bits or surface discolorations that remain on the front? Here’s my last resort. I wrote about it before:

Yes. Silly Putty. I have found that a couple of gentle blots will pick up fuzz and shed bits of color. The trick is NOT to scrub, just support the cloth from the back (I use the top of the stuff’s eggshell container), and press the putty gently onto the affected area – then remove it vertically and quickly. Make sure not to let it dwell on the surface.

I will caution that there is risk doing this. I have no way of knowing if anything exuded by Silly Putty will be a life-limiting factor for the threads or ground in 50 years – if discoloration or other complications might ensue. But the Materials Safety Data Sheet for it doesn’t turn up anything particularly evil, and I am willing to risk it. You will have to make that decision for yourself on your own. Having warned you I take no responsibility if it ends up doing so.

BOOKMAKING 107: THE HUBRIS OF FAULTY LAYOUT (AND PLANNED RECOVERY)

OK. Here I am, showing off my overconfidence in front of everyone. I admit it – I’m not perfect,. Often my enthusiasm gets in the way of prudence, and I forget things like double checking all measurements.

And so this happened

Here you see the “knot” I designed as the cheat at the center of the mirrored top and bottom border. It’s just fine – plump and happy. But wait! See that three stitch (6-thread) gap between it and the green border edge line coming in from the right? That shouldn’t be there! The spot the orange arrow indicates SHOULD be the center of that knot, to align with the center axis I’ve designated for this second side of my book cover.

Panic ensues. I go back and look at the entire border bit, from this center back to the right edge…

Nope. I didn’t miscount. The repeat is true. Why then am I off. (A deeper sense of panic sets in.)

I measure the leafy side of the book cover. It’s true to my original planned dimensions. Hmmm…. Can it be?

YES!

It looks like I made a major mistake in my layout that I did not notice when I worked the previous side. I inadvertently added the width of the spine to the width of the first side I stitched, over and above the spine width that’s already there and marked. I have nade a first side that’s marginally too big – about six stitches too big, and a second side with a main field that is no longer centered.

What to do?

I’ve got several choices

  1. Bury the thing in my Chest of Stitching Horrors(tm) and abandon it forever. Nope. Not going to happen. For one, there are witnesses (you); also a major promise of delivery.
  2. Do #1, but begin again. Not going to happen, either. I’ve gotten to far along to set this much effort aside.
  3. Pick out the entire first side and redo – or pick out the entire second side and redo. Tempting (especially the latter) but also not a favored option. While the mistake is real and is six stitches per side, I don’t think it warrants total destruction.
  4. Figure out a way to use as much as possible of the stitching done to date, and adapt. Being a bungie-jump stitcher, this is not the first time that things have gone seriously awry. Adapt. Reuse. Redirect. That’s my way. That’s what I will do.

Taking a moment to let the panic subside (as it usually does once I’ve figured out where the original mistake happened), I look at my options.

First, I point out that while being off six stitches on the front and six on the back sounds like a lot, at the thread count I’m using it’s only 3/16 of an inch per side, at most the book cover will be a teeny bit deep compared to the substrate notebook, but not enough to matter. Second, there is a blank area set aside for the spine – it’s six stitches wide. I can cannibalize it to compensate for half of the overage.

OK. Things are looking more manageable. Because the center of the second side is an eccentric repeat, in spite of my effort to balance it left/right, a skew presentation will not be all that noticeable, not compared to the same error on a totally symmetrical design like the flower-side. I can leave the double sprig and diamond ground section as-is.

For the border, I can leave in what I have, including the tell-tale center knot, and work the left side of the knot to mirror what I’ve already done on the right. If I do that by the time I get to the leftmost edge of this second cover I will be six stitches off count – eating up those six stitches I had set aside for the spine. The front and back covers should meet up along the single green line that marks the rightmost edge of the flower-patterned side above.

I hope. It should work. In theory. (The suspense is palpable.)

Stay tuned!

BOOKMAKING 106: QUESTIONS ON THE VOIDED DIAMOND GROUND

Yesterday’s post has inspired a few really good questions. Thanks for sending them in!

Are you working the diamond background in double running stitch?

Susan wants to know if the background diamonds are being worked totally double sided. I answer that while they certainly can be, in this case I am not bothering to do so.

No one will see the back of this piece once it’s in place on the target book. So I am working mostly, but not entirely in double running. Since I have jumped the gun somewhat and begun the background before all of my foreground motifs are complete, I have to be careful not to get ahead of myself and fill in too much – painting my yellow across the site of a future leaf. Therefore I am mostly working in double running, but reserving the right to pop over to “heresy stitch” to advance my working thread as needed, and to avoid painting myself into a corner, or covering up an area that would need to be picked out later.

There must be gaps where the diamonds don’t meet up with the leaves. Are you working half-stitches to fill in those bits?

Lisa, this is an excellent question, and really observant of you to pick up on the issue! Here’s a diagram illustrating what she was talking about.

Note how in some spots, and especially around the tendrils and lobed leaf sections there is a half-stitch gap between the red outlines of my double leaf, and the yellow diamonds. Now I COULD go and work half stitches to continue the diamonds right up to the edge of the red, but in truth – it doesn’t matter. Because the yellow is so light compared to the red, and I’m working with a relatively heavy thread thickness for the count of the ground, the visual impact of those half-stitches is almost nil. So I cheat, and leave them out all together.

How do you get the diamonds to match up as you go around the leaves?

Another excellent question, Erin! The secret to doing this is NOT to start the diamonds in several spots. Begin it in one place, and grow it out from there, working around obstructions as they are encountered. It’s kind of like a fairy ring, (or if you are computer gaming fan – The Creep). By always extending the pattern area from an established bit of work out into new territory, I stay on target, and my diamonds always align.

Have more questions? Ask away!

BOOKMAKING 105 – ONE COVER DONE. CENTERING ECCENTRIC REPEATS

The first side is done! You can see that I’ve filled the entire defined stitching area, and that I’ve mirrored the border all the way around.

You can also see that I’ve left in the basted lines that mark the flap areas I will need to form the slipcover parts.

Now on to the second side. (I’m not going to call these front and back because I intend to let the recipient decide which one she likes better.)

IF YOU ARE WORKING A BOOK COVER YOU CAN STOP STITCHING HERE. Decorating the back and spine areas is a personal choice. You may want to skip one or both of those in order to finish more quickly. No shame in that, but you’ll have to wait a bit for the finishing instructions because I am going to do both.

Finding a Center Point on an Eccentric Repeat

Centering the pattern for the first side was pretty easy. I had basting stitches that marked the exact center point of my stitching area, and I had a pattern with a lovely swirly flower, complete with a perfectly defined center point. I could have used the center of the yellow lattice, but I chose to make the flower the focal point.

But what about an eccentric repeat? One that doesn’t rely on quadrilateral symmetry like the flower does. Or mostly does – that directional swirly center mixes it up just a bit, but the outline of the flower and lattice is solidly four-square symmetrical – you can flip it up, down or left/right and the outline remains the same.

Here’s the eccentric repeat I’ve chosen for this side:

Wow. Where is the center? The double-leaf sprigs do reverse-mirror up and down, but the reflection point is a box, not a dot (the dots representing the “holes” in our ground cloth). I’ve circled it in red.

We COULD work the piece on skew count compared to the established prior work . That’s one of the advantages of using even weave instead of one of the purpose-woven grounds like Aida, but I don’t want to. I’ve left one two-thread unit as a clear zone between the border and the field on the first side. I don’t want to make that clear zone wider or narrower on this side.

Instead let’s find a better “center dot” location to line up with the the basted center lines. Ideally i want the piece to be visually balanced, in spite of the eccentric repeat. So let’s look in the spaces BETWEEN the sprigs. It just so happens that there is a perfect spot. There is a two-stitch gap between the buds on the curlicues – that tendrils that looks like they end with a berry. I’ve marked the dot between them. That’s the spot I mated with my designated center point in this stitching area.

Here’s the start of my stitching. You can just make out the remains of the basted center line to the left (the vertical one is already too picked out to show on this photo). But I’ve included the Blue Dot that matches up to the chart above. That’s the exact center of my area, and that’s my alignment/starting point for this one.

One thing to remember about aligning eccentric repeats this way – they do truncate around the edges. My chosen area is large compared to the scale of the motif. Several full repeats will fit both up and down and across that field. If I were to employ this filling in a smaller area, instead of looking for a visual center point for the design as a whole, I might place the design so that at least one full repeat was shown, or I might center the most prominent part of it (the leaf) in my area-to-be-filled, and let the rest of the design be cut off as it may.

Here’s an example of trying to shoehorn a larger repeat into a smaller area. The dragon won’t fit cleanly on any one side of the gear shape into which it was jammed. But by moving it around a bit rather than trying to center it cleanly, I was able to get enough of it in to make the thing “legible.”

And I continued on. Just as before I worked my way out to the right, until I got close to but not right up against the area where my border should go. I’m using the same border on both sides of the book, so it was easy to count and copy from established stitching. Once I had aligned the center knot on my basted horizontal center line, I worked down from that to the corner, copying the stitching I had already done on the finished cover. Then with my border established, I went back and filled in more of the field.

I liked the almost-voided effect of the yellow lattice on the first side, so I decided to work this design in true voided style. And since just the other day I found an example of a diamond voided fill on a historical piece, why not?

I’m fairly flying on this second side. Being able to copy the border (and being familiar with it at this point), plus the simplicity of the diamond ground is making this bit quite speedy. What you see above is more or less what I was able to stitch in about four hours total time, spread out over two evenings.

And I am liking this fill. A lot. I may have to use it again. Possibly in combo with border I designed to match. Both are in my free book, Ensamplario Atlantio II.

So. Is all of this clear as mud? Do you have any questions? Are you thinking of working an original project based on these principles? It could be a book, a pincushion, a pillowcase, a box top, a small hanging piece – anything. The same hints on defining a stitching area, centering a design, and working on the fly (as opposed to fully drafting out an entire stitch-for-stitch full project chart) all would be helpful.

Unleash your inner doodler/designer! Go for it! I know you can.

BOOKMAKING 104 – QUESTIONS ON LAYOUT AND DESIGN

On to the rest of the border and filling out the field…

I’ve gotten a few questions and feedback notes on this project. I’ll try to answer.

How do you know where to put the centers and corners?

It’s hard to make out on the in process pix because I snip away/tease out the bits as I encroach upon them, but I have basted guidelines showing me the exact center of my piece both north/south and east/west. They are in light blue thread. I’ve also marked the borders of my stitching area in lilac thread. You can just make out the guideline remnants on the photo below.

Also, if you page back in this tutorial series, you’ll see that I started in the center, then worked out to the right, leaving room for my as-yet-unchosen border. Then I picked one and started stitching. When I neared the corner I looked at what I’d done and doodled up a corner, then worked it. I repeated the process, stitching back to the center and doodling up the center bit, working it on the exact center of my marked stitching area. Then I worked the other side of the center bit mirror image of the established stitching.

No photo description available.
How did you get the second top corner to line up perfectly with your basted edge?

It’s counted. The center line of my stitching area is at the exact center of the area to be stitched. That means if there are (picking a number at random) 43 stitches to the right of it, there will be 43 to the left. If my pattern is symmetrical, it’s easy to see when you’ve gotten to the same point on the left as you ended off on the right.

What would you have done if you were one thread off?

It happens. Sometimes for every bit of measuring, exact folding, and counting (and especially on even weave) that center line ends up being one thread or even one full stitch off. In this case – no big deal. I would work my repeat totally symmetrical as I have above, and “push” that tiny bit of overage into the spine of the book.

How do you keep track of where you are with all those colors?

I admit it’s a challenge, and this design would be a lot easier in monochrome. I don’t like to leave long skips on the back, so for the most part, there are a lot of starts and stops. The longest leap I will take is three stitches, and I prefer not even to do that. This means that in the main field of flowers, while I can keep a baseline double running logic chaining flower after flower together, those little crosshatched interlaces of yellow between them are “islands” – each one begun and ended off separately.

You can see in the photo at the top of the page that there are two green threads dangling off the right side of the hoop. Those are the strands I am using for the border outlines. Rather then ending them off at the edge of my hoop, I’ve chosen to keep them “alive.” Pretty soon I’ll be advancing the hoop to finish off the bottom of the stitched area, and I’ll use them up as the border area progresses. Sometimes I’ll take a pin and insert it in the waste edge of my design (or another spot where any perturbing of the ground cloth weave will not matter), then wind the excess thread around it to keep it up and out of the way while I stitch nearby.

And in the border area at the top – I just did some of the green striped “column” that runs down the center of my border. I know that the red ribbon that wraps it is three stitches wide. I started at the edge of the existing red ribbon and worked “heresy style” across the first line, then hopped down and worked standard double running for the center one, and again for the one after that. That meant my working thread was now positioned at the left side of that block of three stripes, and ready to hop over three again to begin the next block of three stripes. I kept going in this manner until I used up my green working thread. Next I will go back and fill in the red ribbon, and finish up with the short spurts of yellow. And yes, that does mean a lot of ends. I would never attempt a multicolor piece that was totally double-sided.

It’s hard enough to pick a pattern, now you want me to design centers and corners, too?

Perhaps I did get a bit ahead of myself and I could have chosen a simpler border. One that isn’t directional like this one with its wrapping is. And mirroring around the center can look a bit daunting, as can doodling up a custom join. But there’s no reason to be intimidated.

I noodled up #1 in the set below. But I didn’t have to. My treatment could have been much simpler.

#3 for example ignores mirroring, directionality, centers, and corners. It just starts at a random point of the repeat, goes across the area to be covered, and arbitrarily ends at the edge of the desired space. Then it starts up again, butted against the bit already stitched. And it doesn’t matter if it’s centered or truncated. (By the way, plain butted pieces with truncated rather than an elegantly ended or mitered repeat is the most represented treatment for corners in museum collections of historical stitching)

In #2 and #4, I’ve kept the mirroring (but I didn’t have to) and inserted small simple shapes to fill the contested areas. #2 uses plain old squares. Nothing fancy. #4 reserves those spots for personalization. Initials, dates, small stars, whatever. What I’m trying to show here is that there is no one right way, and all treatments look good. Go simple, go complex. It doesn’t matter, your piece will be beautiful, and best of all – it will be uniquely yours.

More questions?

Idly curious or wanting to do you own book cover? All is good. Happy to help. Got a question? Send it in.

BOOKMAKING 103 – BORDERS

We go on with the removable book slipcover project.

Step 9: Laying Out and Choosing a Border

Last time I had begun working the field pattern for the first cover. I centered it on the center point of the available area, and began working left, right, up and down. Since the total area isn’t very large compared to the span of the repeat, pretty soon I got close enough to my first edge to begin considering what I wanted to do with the border. I stopped well shy of the basting line that indicates the edge of my territory:

In the photo above you can see there’s lots of room to go, but I need to determine exactly how much room there is, so I can select, adapt, or draft up my border design. I’ve decided that whatever I do, it will be bounded both inside and out by a single line of deep green (DMC #890). (I like the contrast with the red and yellow). So taking care to make sure that I have FULL STITCH UNITS between the basted guide line and my stitching area – meaning even multiples of two threads – I start working my outermost solid green line.

Lucky me – it turns out that my basted edge falls exactly 13 stitch units (26 threads) from my established work. Had there been an odd number of threads I would have established my line one thread to the outside of my basted line. Better a tiny bit too large than a tiny bit too small. And yes, I counted the number of threads between the top basted line and the established work, too. It’s even bigger, so I am safe.

My border can be anything up to 13 stitches. But I don’t want one that wide. About half that is enough. So I went thumbing through my various stitch collections. I wanted one that would contrast nicely with the field and not fight with it, and would accommodate using up to three colors, including the newly introduced green.

I didn’t find a pre-drafted, complete border that I liked in this application, but I did come up with this all-over design, presented in Ensamplario Atlantio, my first freebie, in Part 3, Plate 16:91.

It looks complex, but it’s just a simple ribbon-wrapped column, repeated multiple times. If you abstract just one of the columns and add a line of framing stitches both left and right, it spans only 6 stitches across. A perfect size, and there are several color-use possibilities as well.

Based on the design above, I drafted this out and started stitching. Note that I began by making a nice, neat corner.

For the record, these and all charts for linear stitching on this blog have been produced using the open source drafting software package GIMP. Here’s a free tutorial for how I do it (read up from the bottom for best logic).

Step 10: Stitching the Border

Just go for it!

The observant will note that I started stitching from the corner and worked the border down, then went back and filled in my field pattern, stopping one unit away from the border’s inner line. I don’t care at all that my field pattern is truncated. I COULD have stopped at the last whole or half-repeat, but to me, for this particular work, it doesn’t matter.

I am also not in the least bit concerned about how to make the design fit either the length or width of my book. I intend to work from the corner out towards the center of each side, approaching but not connecting at the center. Yet.

The next steps will fill work more of the border across the top of the piece, then fill in a bit more of the field. But I will stop the border and leave a gap in the center. It’s my intent to work the other corners similarly, but in mirror image to this one. Since everything is done on the count and is exactly even, I will be able to draw up a “join” or top/bottom/left/right border center kludge of some type to unify the border as a whole. And I bet that had I not confessed this here, you would have never known I got this far without planning it all out in advance.

Bonus Bit: The Back

For the folks who have asked to see the back, here it is flipped over. You can see the wrapped inner hoop of my frame and its attached support stick.

As stated, I tend to work in double running, using (mostly) reversible logic, but I am not a slave to it on pieces that are not intended to be seen on both sides. There are lots of knots. And you can see that I’ve used heresy stitch in laying down my initial border outlines, and in advancing the border in general. The short length color runs necessitated by its rather fiddly color changes make it much easier to plot out than the double-pass of double running.

MAKING BOOK

OK. Now that I’ve armed a whole bunch of people with a wealth of counted all-over designs – what to do with them?

Pretty much anything you want. While samplers are the most common, there are lots and lots of things you can make that don’t involve using up precious wall space. Pincushions (either plain square or rectangular pillows, or fancy biscornu); pillow or cushion covers; napkins, doilies, and tablecloths; kerchiefs (aka for the historically-minded – forehead cloths); tray or coaster inserts (using pre-made items intended to showcase a piece of stitching or painting); zip or tied pouches or folios of various types – jewelry or lingerie rolls are examples; slip-in cases for sunglasses, phones, or tablet devices; small rice or lentil-filled handwarmers or heating pad pillows (warmed in the microwave, for gentle comfort or cold fingers); greeting cards or festive ornaments; all are examples of things that might sport your stitching.

But I want to revisit one project in particular – the book cover.

Making a Slip Cover for a Small Notebook

This is a general logic recipe for making a reusable slip cover in for a small notebook, using the same method as the standard brown-paper-bag covers kids of earlier eras employed to protect school-issued textbooks. The basic logic can be adapted to cover any size book. I’ve written this with special steps for counted embroidery project, but any fabric or stitching style can be used.

In this particular case I covered two small pocket notebooks, roughly equivalent in size to Moleskines, but of a far less expensive make. They are about 3.5 inches wide, by 5.5 inches tall, and roughly 0.5 inches thick across the spine (about 8.9 x 13.4 x 1.3 cm). They came with an elastic cord to keep them closed/mark one’s place, and were about half as expensive as the fancy name brand ones.

Layout

I wanted to know how big a piece of fabric I would need. Having measured a notebook, I did a mockup of the cover, drawing the shapes to size on a piece of paper to make my pattern. I used a brown paper grocery bag to do my layout and mockup (fitting it onto my target notebook to make sure it all worked. That pattern is now long gone, but here’s the logic I used. I strongly suggest making a mock-up and “dry fitting” it before you begin the project, just to make sure that the dimensions work. Note that some books have thicker cardboard covers or heavier spines than others, and may require a bit more “wiggle room” to be added to the measurements below – even if the books have the same general dimensions as the ones I used. If your book is significantly larger than mine you may want to increase the depth of the flaps all the way around. But you should not need to add more than the indicated amount beyond the stitching area (the red rectangle below). The overage of the grey area is just there to provide purchase for a hoop or frame.

Note that I’ve allowed a little bit of extra width for the spine, so that there is enough slack for the book to open and close properly. I’ve also allowed lots of extra room around the stitching area, to accommodate use of my hoop or snap frame. You can use a smaller piece of cloth closer to the dimensions of the book cover itself if you like, but be aware that frequent repositioning of the hoop to get close to the edges is a pain in the neck, and all of that tugging and yanking isn’t good for your threads or ground either. And if you’re mounting this on a flat or scrolling frame, tensioning the sides and ends very close to the stitching area can lead to distortion, so having a bit of extra room for the stress to even out is also good.

For my standard size pocket mini-notebook, I’ll need a piece of ground fabric that’s about 13.25 x 11 inches (33.7 x 27.9 cm – all metric measurements are rounded off). If I intended to hem my edges of my entire ground cloth prior to starting (as opposed to whipping or serging), I’d add a half inch all the way around to this measurement.

Selecting the Fabric

What type of fabric? Well, whatever you enjoy working. This project will be a tiny bit easier to lay out on even weave, but not overly so. You can use Aida, Monk’s Cloth, Fiddler’s Cloth, Hardanger, in whatever count is most comfortable. But the count you select will also be key for what design you select. The lower the count (fewer stitches per inch), the larger your finished iteration of the design will be and the fewer repeats of it will fit in these designated spaces. If for example you want to stitch 11 count Aida, our front cover – only 3.5 inches wide would mean your total stitching area is about 38 stitches wide (rounding down). A repeat of say 8 stitches across would appear 4 full times plus some fragment at left and right (more on this later). A repeat that’s 14 stitches across would show in full only twice, with a fragment at the left and right sides.

Why would layout be easier to do on even weave as opposed to Aida or one of the others? Because you can determine the center point more accurately on even weave. In one of the purpose woven grounds with their well established holes (and especially in the fewer-stitches-per-inch sizes), the centermost line of holes may be off the exact center of the piece just a teensy bit, and may be enough to annoy you.

One last suggestion – whip, or serge your edges after you cut your fabric to size. Some people use tape. I don’t recommend it because of the adhesive residue.

Marking the Fabric

In this type of project, where we don’t intend to graph out every single stitch beforehand, knowing where the edges and center lines are is very important. Some people use water soluble markers or pencils for this. I’m old fashioned. I would baste. Some people are very specific in technique, taking each basting stitch over 4 or 5 stitch equivalents to aid in counting, but I’m pretty haphazard. I just establish my lines and don’t try to make my basting stitches even.

To transfer the dimensions of the diagram above to my cloth, I’d start more or less in the center and measure out from there, basting in lines, probably in a couple of colors. I use plain old sewing thread; spools of thread inherited from my grandmother – 100% cotton, in pale pastels, too fragile for use in seaming, but perfect for this. I’d outline my stitching fields using one color (the heavy red lines on the diagram). Then I’d mark the center lines both north/south and east/west (the thin blue lines). You may find that you have either a line of holes or a full stitch at the very center of your front cover, back cover, and spine. Decide now if you are a perfectionist or not, and if your purpose woven cloth forces you to mark at one side or the other of any center column/row of stitches, which side of the center you have marked. More on this below.

There’s no strong reason to mark the no-sew flap areas at this point, but they are on the diagram so you know they exist, and their width should not be forgotten.

Choosing your Design

Elsewhere on the site you’ll find books and books of fills and other patterns. Thumb through. Pick something that appeals to you, that’s a good fit for your chosen ground fabric’s count. BUT also be aware of the Center Problem.

Some patterns have a specific center line. They have even repeats – 4 stitches, 8 stitches, 22 stitches – whatever. Each repeat is an EVEN number of stitches. These repeats mirror evenly left and right of an line. Other designs have ODD numbers of stitches in one repeat – 5 stitches, 9 stitches, 11 stitches – again any number but an ODD one. That means that there is a center stitch in these designs. Here are examples:

The wavy plumes (shown in two variants) are an EVEN 14-stitch repeat with a specific center line. The framed pears is an ODD 15-stitch repeat. It’s center is the X unit where the four pear stems meet.

Why does this matter? If you are a perfectionist using Aida (see above) and the center of your area to be stitched is in the middle in between two columns of holes, look for an ODD stitch repeat. If the center of those areas work out neatly to align with a column of holes pick an EVEN stitch repeat.

Now you know why I mentioned that layout on even weave is easier. Not being forced into using specific hole locations makes fudging that center line easier and if your heart is drawn to either an odd or even repeat, any finagling you might do to make placement will be less obvious.

Choosing Thread and Stitching

Here I am of less help, especially for folk using Aida. I can tell you that on 32-38 count linen (16-19 stitches per inch) I usually use one or two plies of silk or cotton floss. 40-50 count linen (20-25 stitches per inch), I use one ply. And that I run the thread through beeswax prior to stitching. If you are using a lower count ground I’m afraid you’ll have to experiment to see whether you like 1, 2 or 3 plies the best.

In any case, no matter what your ground is, your basted lines will tell you exactly where the center of your area to be stitched is. Find the center of your chosen pattern, and start from there. Double running or back stitch – even heresy stitch – it doesn’t matter. Start in the center and work your way out. You can choose to work the ENTIRE stitched area – front cover, spine and back cover as one unit, and start in the center of the spine. Or you can work the front and back covers either identically or different; and leave the spine unworked, or treat it in another manner (perhaps a narrow border, solidly covered with cross stitches, or anything else you dream up). There is no wrong here.

When you get close to the basting line that describes the edge of the section you are working on pause. Decide whether you want to continue the design right up to the edge, or if you want to stop (possibly at the natural edge of your repeat, or at some unobtrusive place in it) and save the remaining area to do a border. That’s what I decided to do on my two sample books above. Any narrow geometric band – even just parallel straight lines – can be used to frame the center design and draw the eye away from truncation of the center design.

Finishing the Piece and Assembly

Once everything is all stitched, you can do a gentle wash and iron (nothing with big agitation, harsh detergent, or high heat). Or not. It’s up to you. Now is the time to draw or baste-mark those extra flaps. If you are going to serge them you can mark them and cut to exact size. Note that the ONLY places where secure edge treatment is mandatory are shown in green below. I strongly recommend hemming for those, although serging will work in a pinch. The other edges can be fray check secured or even left plain (they’ll never see the light of day again). Personally, I mark the flaps, and cut leaving a quarter inch seam allowance for the green bits that I turn back and hem, doing a veeerrrryyyy careful diagonal cut at the corner where the front and back inner flaps meet the top and bottom flaps. When I turn back the outer points of the front and back inner flaps and hem them down, I cut off the triangular excess to reduce bulk.

The top and bottom flaps do not need to be stitched down. Ironing them flat is enough. The final step is folding in the back and front inner flaps and stitching them to the front and back, along the edges of the book. This leaves a neatly edged pocket that will slide over the book cover. If the book cover doesn’t fit, feel free to snip it just a bit so that it slides in nicely. No one will ever know.

One last refinement. Many of these books come with an elastic loop that can be used to hold the book closed or mark a page. It’s useless in this application. I snip it off the book prior to fitting the cover. Instead, to serve as a bookmark, I stitch on a length of narrow ribbon, attaching it at the little red dot marked on the diagram above.

OK. Now armed with the basic how-to. Let’s see what you can come up with yourself!